Electronic devices have significantly influenced the development of many aspects of modern society, such as telecommunications, entertainment, education, health care, industry, and security. The main driving force behind the advancement of electronics is the semiconductor industry, which continually produces ever-more sophisticated electronic devices and circuits in response to global demand. The semiconductor industry is one of the global economy's largest and most profitable industries, with annual revenues exceeding $481 billion in 2018. The electronics industry also encompasses other branches that rely on electronic devices and systems, such as e-commerce, which generated over $29 trillion in online sales in 2017. (Full article...)
These are Good articles, which meet a core set of high editorial standards.
Image 1
m-derived filters or m-type filters are a type of electronic filter designed using the image method. They were invented by Otto Zobel in the early 1920s. This filter type was originally intended for use with telephone multiplexing in carrier telephony systems and was an improvement on the existing constant k type filter. The main problem being addressed was the need to achieve a better match of the filter into the terminating impedances. In general, all filters designed by the image method fail to give an exact match, but the m-type filter is a big improvement with suitable choice of the parameter m. The m-type filter section has a further advantage in that there is a rapid transition from the cut-off frequency of the passband to a pole of attenuation just inside the stopband. Despite these advantages, there is a drawback with m-type filters; at frequencies past the pole of attenuation, the response starts to rise again, and m-types have poor stopband rejection. For this reason, filters designed using m-type sections are often designed as composite filters with a mixture of k-type and m-type sections and different values of m at different points to get the optimum performance from both types. (Full article...)
Introduced in 2003, HDMI largely replaced older analog video standards such as composite video, S-Video, and VGA in consumer electronics. It was developed based on the CEA-861 standard, which was also used with the earlier Digital Visual Interface (DVI). HDMI is electrically compatible with DVI video signals, and adapters allow interoperability between the two without signal conversion or loss of quality. Adapters and active converters are also available for connecting HDMI to other video interfaces, including the older analog formats, as well as digital formats such as DisplayPort. (Full article...)
This approach is especially useful in the design of mechanical filters—these use mechanical devices to implement an electrical function. However, the technique can be used to solve purely mechanical problems, and can also be extended into other, unrelated energy domains. Nowadays, analysis by analogy is a standard design tool wherever more than one energy domain is involved. It has the major advantage that the entire system can be represented in a unified, coherent way. Electrical analogies are particularly used by transducer designers, by their nature they cross energy domains, and in control systems, whose sensors and actuators will typically be domain-crossing transducers. A given system being represented by an electrical analogy may conceivably have no electrical parts at all. For this reason domain-neutral terminology is preferred when developing network diagrams for control systems. (Full article...)
Image 4
A Leslie speaker in a clear plastic cabinet The Leslie speaker is a combined amplifier and loudspeaker that modifies the sound of an electric musical instrument by rotating a baffle chamber (drum) in front of the loudspeaker. A similar effect is provided by a rotating system of horns in front of the treble driver. It is most commonly associated with the electric Hammond organ, though it was later used for the electric guitar and other instruments. A typical Leslie speaker contains an amplifier, a treble horn and a bass speaker—though specific components depend upon the model. Some models have two speed settings, known as chorale and tremolo.
The speaker is named after its inventor, Donald Leslie, who began working in the late 1930s to get a speaker for a Hammond organ that better emulated a pipe or theatre organ, and discovered that baffles rotating along the axis of the speaker cone gave the best effect. Hammond was not interested in marketing or selling the speakers, so Leslie sold them himself as an add-on, targeting other organs as well as Hammond, beginning in 1941. The sound of the organ being played through his speaker received national radio exposure across the US, and it became a commercial and critical success, becoming popular with jazz organists. In 1965, Leslie sold his business to CBS who, in 1980, sold it to Hammond. Suzuki Musical Instrument Corporation subsequently acquired the Hammond and Leslie brands. (Full article...)
Image 5
A time-domain reflectometer; an instrument used to locate the position of faults on lines from the time taken for a reflected wave to return from the discontinuity. A signal travelling along an electrical transmission line will be partly, or wholly, reflected back in the opposite direction when the travelling signal encounters a discontinuity in the characteristic impedance of the line, or if the far end of the line is not terminated in its characteristic impedance. This can happen, for instance, if two lengths of dissimilar transmission lines are joined.
This article is about signal reflections on electrically conducting lines. Such lines are loosely referred to as copper lines, and indeed, in telecommunications are generally made from copper, but other metals are used, notably aluminium in power lines. Although this article is limited to describing reflections on conducting lines, this is essentially the same phenomenon as optical reflections in fibre-optic lines and microwave reflections in waveguides. (Full article...)
Image 6
The circuit topology of an electronic circuit is the form taken by the network of interconnections of the circuit components. Different specific values or ratings of the components are regarded as being the same topology. Topology is not concerned with the physical layout of components in a circuit, nor with their positions on a circuit diagram; similarly to the mathematical concept of topology, it is only concerned with what connections exist between the components. Numerous physical layouts and circuit diagrams may all amount to the same topology.
Strictly speaking, replacing a component with one of an entirely different type is still the same topology. In some contexts, however, these can loosely be described as different topologies. For instance, interchanging inductors and capacitors in a low-passfilter results in a high-pass filter. These might be described as high-pass and low-pass topologies even though the network topology is identical. A more correct term for these classes of object (that is, a network where the type of component is specified but not the absolute value) is prototype network. (Full article...)
Image 7
The iPhone 6 and iPhone 6 Plus are smartphones that were developed and marketed by Apple. They are the eighth generation of the iPhone, succeeding the iPhone 5, iPhone 5c and iPhone 5s, and were released on September 19, 2014. The iPhone 6 and 6 Plus respectively include larger 4.7-inch and 5.5-inch displays, a faster processor, upgraded cameras, improved LTE and Wi-Fi connectivity and support for a near-field communications-based mobile payments offering. The iPhone 6 and iPhone 6 Plus were replaced as the flagship devices of the iPhone series by the iPhone 6s and iPhone 6s Plus on September 9, 2015.
The iPhone 6 and 6 Plus received positive reviews, with critics regarding their redesign, specifications, camera, price point, and battery life as improvements over previous iPhone models. However, aspects of their design were criticized, including plastic strips on the rear of the device for its antenna that disrupted the otherwise metal exterior, and the screen resolution of the standard-sized iPhone 6 being lower than other devices in its class. The iPhone 6 sold extremely well, becoming the best-selling iPhone model and the most successful smartphone to date. The iPhone 6 and 6 Plus supported iOS 8, 9, 10, 11 and 12 before being dropped by iOS 13. (Full article...)
Image 8
Figure 1. Waveguide slotted line Slotted lines are used for microwave measurements and consist of a movable probe inserted into a slot in a transmission line. They are used in conjunction with a microwave power source and usually, in keeping with their low-cost application, a low cost Schottky diode detector and VSWR meter rather than an expensive microwave power meter.
Slotted lines can measure standing waves, wavelength, and, with some calculation or plotting on Smith charts, a number of other parameters including reflection coefficient and electrical impedance. A precision variable attenuator is often incorporated in the test setup to improve accuracy. This is used to make level measurements, while the detector and VSWR meter are retained only to mark a reference point for the attenuator to be set to, thus eliminating entirely the detector and meter measurement errors. The parameter most commonly measured by a slotted line is SWR. This serves as a measure of the accuracy of the impedance match to the item under test. This is especially important for transmitting antennas and their feed lines; high standing wave ratio on a radio or TV antenna can distort the signal, increase transmission line loss and potentially damage components in the transmission path, possibly even the transmitter. (Full article...)
The image method of filter design determines the properties of filter sections by calculating the properties they would have in an infinite chain of identical sections. In this, the analysis parallels transmission line theory on which it is based. Filters designed by this method are called image parameter filters, or just image filters. An important parameter of image filters is their image impedance, the impedance of an infinite chain of identical sections. (Full article...)
Image 10
The ZenFone6 is a 2019 Android-based smartphone that was manufactured, released, and marketed by Asus. It is the only release in Asus' sixth-generation ZenFone lineup and directly succeeds the ZenFone 5Z. Asus chairman Jonney Shih unveiled the ZenFone6 on 16 May 2019 in Valencia, Spain, and it was released in Spain the following day.
The ZenFone6 has a larger 6.4-inch (160mm) display, a faster processor, and upgraded cameras than the ZenFone 5Z. The ZenFone 6's flip-up camera module doubles as a front-facing camera. It is the first mobile device Asus released after restructuring its smartphone division in late 2018. The ZenFone 6 was released in the Indian market as the "Asus 6Z". (Full article...)
Image 11
The Electro-Dynamic Light Company of New York was a lighting and electrical distribution company organized in 1878. The company held the patents for the first practical incandescent electric lamp and electrical distribution system of incandescent electric lighting. They also held a patent for an electric meter to measure the amount of electricity used. The inventions were those of Albon Man and William E. Sawyer. They gave the patent rights to the company, which they had formed with a group of businessmen. It was the first company in the world formally established to provided electric lighting and was the first company organized specifically to manufacture and sell incandescent electric light bulbs.
Man, an attorney from New York City, supplied money for experimentation to Sawyer, an electrical engineer. This partnership developed into the Electro-Dynamic Light Company that brought in other investors that became partners. Sawyer devised a unique electrical distribution system where electrical power could be obtained anywhere in the city from an electrical generator with the turn of a switch to light up electric lamps to produce glowing light like a gas lamp. It was unique in that it produced this power without consumers having to maintain local galvanic batteries and at a fraction of the cost of producing the same lighting as from gas lamps. Other features of the system were that safety devices were built in to prevent the early destroying of the other electric lamps in the circuit should there be a power surge due to a lamp burning up early and leaving the distribution circuit. The patents for the Man and Sawyer system were in place before any other electrical companies had similar systems. (Full article...)
Image 12
The Sinclair Sovereign was a high-end calculator introduced by Clive Sinclair's company Sinclair Radionics in 1976. It was an attempt to escape from the unprofitable low end of the market, and one of the last calculators Sinclair produced. Made with a case of pressed steel that a variety of finishes, it cost between £30 and £60 at a time when other calculators could be purchased for under £5. A number of factors meant that the Sovereign was not a commercial success, including the cost, high import levies on components, competition from cheaper calculators manufactured abroad, and the development of more power-efficient designs using liquid-crystal displays. Though it came with a five-year guarantee, issues such as short battery life limited its usefulness. The company moved on to producing computers soon afterwards.
The iPhone 5s is a smartphone that was developed and marketed by Apple. It is the seventh generation of the iPhone, succeeding the iPhone 5, and was unveiled in September 2013 alongside the iPhone 5c. It was the last iPhone to have Steve Jobs involved in its design.
The iPhone 5s has almost the same external design as well as the same 4-inch screen as its predecessor, the iPhone 5. The 5s received a new white/gold color scheme in addition to white/silver and space gray/black. The 5s features upgrades mostly in the form of internal hardware; it introduced the Apple A764-bit dual-core system-on-chip, the first 64-bit processor to be used on a smartphone, accompanied by the M7 "motion co-processor". A redesigned home button with Touch ID – a fingerprint recognition system which can be used to unlock the phone and authenticate App Store and iTunes Store purchases – was also introduced. The camera was updated with a larger aperture and a dual-LED flash optimized for different color temperatures. EarPods, which were introduced the year prior and had been shipping with the iPhone 5, were included in the box. (Full article...)
Image 14
Foster's reactance theorem is an important theorem in the fields of electrical network analysis and synthesis. The theorem states that the reactance of a passive, lossless two-terminal (one-port) network always strictly monotonically increases with frequency. It is easily seen that the reactances of inductors and capacitors individually increase or decrease with frequency respectively and from that basis a proof for passive lossless networks generally can be constructed. The proof of the theorem was presented by Ronald Martin Foster in 1924, although the principle had been published earlier by Foster's colleagues at American Telephone & Telegraph.
The theorem can be extended to admittances and the encompassing concept of immittances. A consequence of Foster's theorem is that zeros and poles of the reactance must alternate with frequency. Foster used this property to develop two canonical forms for realising these networks. Foster's work was an important starting point for the development of network synthesis. (Full article...)
Image 15
Late version Quad "ESL-57" loudspeaker with black grilles and rosewood end caps
The Quad Electrostatic Loudspeaker (ESL) is the world's first production full-range electrostatic loudspeaker, launched in 1957 by Quad Electroacoustics, then known as the Acoustical Manufacturing Co. Ltd. The speaker is shaped somewhat like a home electric radiator curved slightly on the vertical axis. They are widely admired for their clarity and precision, but known to be difficult speakers to run and maintain.
The original ESL, in production between 1957 and 1985, has been hailed in Sound & Vision as one of the most important speakers of the 20th century. It was succeeded in 1981 by the ESL-63, which remained in production until 1999. As of 2013, Quad maintains four electrostatic speakers in its range. (Full article...)
Capacitance is a measure of the amount of electric charge stored (or separated) for a given electric potential. The capacitance of the majority of capacitors used in electronic circuits is several orders of magnitude smaller than the farad. The energy (measured in joules) stored in a capacitor is equal to the work done to charge it.
In a capacitor, there are two conducting electrodes which are insulated from one another. The charge on the electrodes is +Q and -Q, and V represents the potential difference between the electrodes. The SI unit of capacitance is the farad; 1 farad = 1 coulomb per volt.
The capacitance can be calculated if the geometry of the conductors and the dielectric properties of the insulator between the conductors are known, such as above, where; C is the capacitance in farads, ε is the permittivity of the insulator used (or ε0 for a vacuum), A is the area of each plane electrode in square metres, d is the separation between the electrodes in metres. The equation is a good approximation if d is small compared to the other dimensions of the electrodes.
... that in 2019, Chinese electronics company Xiaomi posted a video of their third-quarterly financial report featuring a parody of the anime song "Renai Circulation"?
... that Alca Electronics was liquidated after being sued by Sega for copying a game, even though their major distributor was one of Sega's founders?
... that police investigating rapist Zhenhao Zou had to develop custom computer code to examine more than 9million WeChat messages on his electronic devices?
... that the American electronic artist Ships In The Night makes synthwave music with melodies inspired by bird songs, church bells, and trains?
Consumer showcase
Amateur radio, often called Ham radio, is a hobby and public service enjoyed by about six million people throughout the world. An amateur radio operator uses advanced radio equipment to communicate with other radio amateurs for public service, recreation and self-training.
Amateur radio operators have personal wireless communications with friends, family members, and even complete strangers. They support the community with emergency and disaster communications.
